Automotive

DATASHEET 2N2905 PDF

2N Low Power Bipolar Transistors. Page 1. 07/04/06 V Features: . Disclaimer This data sheet and its contents (the “Information”) belong to the. 2N Datasheet, 2N PNP Switching Transistor Datasheet, buy 2N Transistor. 2N Transistor Datasheet pdf, 2N Equivalent. Parameters and Characteristics.

Author: Yojin Vudokazahn
Country: Costa Rica
Language: English (Spanish)
Genre: Science
Published (Last): 8 April 2016
Pages: 278
PDF File Size: 3.33 Mb
ePub File Size: 12.79 Mb
ISBN: 971-1-64200-616-5
Downloads: 22631
Price: Free* [*Free Regsitration Required]
Uploader: Sall

Current Drains out through emitter, normally connected to ground.

Current flows in through collector, normally connected to load. Complete Technical Details can be found dafasheet the datasheet given at the end of this page. The maximum datadheet of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin.

When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. This stage is called Saturation Region.

2N2905 2N2907

When base current is removed the datasheer becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. Datashheet it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle. Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits.

  GUNDER FRANK TEORIA DE LA DEPENDENCIA PDF

So if you looking for an NPN transistor that could switch loads or for decent amplification then 2N might the right choice for your project.

The 2N is a NPN transistor and is normally used as a switch in many circuits. Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below. Another important thing to keep in mind, while using a transistor as switch is the base resistor. This resistor is connected to the base pin of the transistor to limit the current flowing through the base.

PNP, Met, 60V mA, GP Amp & Sw – 2N

As we know the transistor is a current controlled device meaning, we have pass some current I B datashee the base of the transistor to turn it on. The value of this current can be calculated by the required amount of current that will be consumed by the load.

Here lets us assume the load here consumes around mA maximum so our collector current I Dayasheet mA.

To make this current flow through the transistor the value of base current I B can be calculated using the below formula:. Where h FE, is the current gain of the transistor which in our case is In our case for a collector current of mA we have to pass a base current of 16mA.

  FROST A.J.AND PRECHTER ROBERT R.ELLIOTT WAVE PRINCIPLE TENTH EDITION PDF

So to calculate the resistor value of the base we can use the formulae. Where Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1.

So the value if R B will be. However this vale will not be very accurate because the transistor will have an internal voltage drop across the dztasheet current, so it mostly experimental to get daatsheet maximum current from the transistor.

2N Datasheet(PDF) – Semicoa Semiconductor

But this calculation will lead to the closest value to start with. Submitted by admin on datashee June To make this current flow through the transistor the value of base current I B can be calculated using the below formula: Amplifier modules like Audio amplifiers, signal Amplifier etc.

TL — Programmable Reference Voltage.